Standardization + Regulation | Jun 15, 2012

Photo-Biological Safety

There’s a lot of talk about ‘Photo-Biological Safety’ in the LED lighting world these days. Mainly because on 27 April 2010 the ‘Control of Artificial Optical Radiation at Work Regulations’ came into effect in UK law, enforcing light exposure limits in the workplace.

So what’s it all about?  A little Googling leads one fairly readily to an international standard:
BS EN 62471:2008 Photobiological safety of lamps and lamp systems.

For a mere £182 you can own a copy! Unfortunately, however, this is where for many folk it all starts getting horribly complicated.  For this is no bedtime read. It is 52 dense pages of physics, mathematics & biology – more like a PhD thesis than an International Standard!

So this overview aims to unravel some of the mystery of Photo-Biological Safety and its guardian standard, BS EN 62471. It must be noted that this standard is also referenced in the EU Low Voltage Directive so must be considered when assessing products for electrical safety (products outside the LVD could be included via the General Product Safety Directive).

Let’s start at the end and look at the output of the standard. This is fairly simple – categorisation of lamps and luminaires into ‘Risk Groups’ with associated ‘Exposure Limits’. There are 4 Risk Groups defined:

Risk Group 3 – High Risk
Risk Group 2 – Moderate Risk
Risk Group 1 – Low Risk
Exempt Group

The ‘Risk’ referred to is subdivided into the risk of physical harm arising from exposure to 8 different categories of light ranging from the Ultra Violet to the Infra Red, each with associated maximum exposure times. It is important to note that BS EN 62471 only defines these risk groups – it does not mandate any product labelling or such as is done eg by the Laser Safety standards. So the standard is really only a metric for photobiological risk, rather than a control.

That’s the easy bit.  The challenge for the luminaire manufacturer is figuring out how to assess which Risk Group a lamp or luminaire is in – i.e. how to interpret and use the standard.  To cut a long story short, the answer is by means of a large number of optical measurements and a lot of mathematics!  In practice, it’s necessary to make full spectral photometric measurements of a sample lamp/luminaire.  Processing the measurement data can then be performed mechanically e.g. by spreadsheet or commercially available software.

In summary then, light sources that come under the Low Voltage Directive need to be assessed for photobiological safety – but no action is specifically required by the referenced standard.  And all luminaire and lamp manufacturers need to be aware of the implications of the Artificial Optical Radiation Directive as do employers in general.   

Forge Europa can assist manufacturers to evaluate LED component safety with our first class testing facilities. For more information talk to our experts on +44(0) 1229 58000 or visit the design verification section of our website.

For more information, please contact       Sarah Simpson
Forge Europa

Tel: (01229) 580 000      
Email: sarah@forge-europa.co.uk

FEATURED

When Very High Light Output and Efficiency are Required for Demanding Applications, New LUXEON 7070 Checks All the Boxes

When Very High Light Output and Efficiency are Required for Demanding Applications, New LUXEON 7070 Checks All the Boxes More lumens, higher efficacy, and lower system costs are the driving forces behind new designs for a broad range of indoor and outdoor high light output applications. Lumileds new LUXEON 7070, introduced today, is designed to outperform similar lead-frame and ceramic high-power solutions with ... Read more »

FEATURED

NEW Extreme High Power LEDs Deliver Best Optical Performance

NEW Extreme High Power LEDs Deliver Best Optical Performance New XLamp® XHP70.3 LEDs deliver the best lumen density, reliability and optical control available in a 7x7 mm footprint.   Read more »

FEATURED

Edison Opto UVA + W & UVC Series Customize Design Solution

Edison Opto UVA + W & UVC Series Customize Design Solution Edison Opto offers customized UVA + White and UVC solutions for continuous disinfection to reduce bacteria and airborne viruses. In the wake of the global outbreak of COVID-19, the people’s need for anti-epidemic, sterilization, and anti-virus products has escalated, ranging from portable ... Read more »

EDITORIAL

deLIGHTed Talks: Good Light – Good Life in Wintertime, November 3, 2021

deLIGHTed Talks: Good Light – Good Life in Wintertime,  November 3, 2021 The Good Light Group, together with the Society for Light Treatment and Biological Rhythms (SLTBR), the Daylight Academy (DLA), the International Association of Lighting Designers (IALD), and Luger Research (LR), are organizing and presenting the “Good Light – Good Life” lectures. The webinar ... Read more »

page_peel